The Engineering Behind Our Waterproof Sheets: What TPU Lamination Actually Is

The Engineering Behind Our Waterproof Sheets: What TPU Lamination Actually Is

Eroticgel waterproof fitted sheet — Dacron and Spandex with TPU lamination

5 min read

Our Standard and Extreme waterproof fitted sheets share a build: a Dacron and Spandex fabric with a TPU waterproof coating bonded to one side. This post explains what each of those layers is, why we chose them, and how the result compares with vinyl.

If you're comparing the different sheets in the range for a purchase decision, the buyer's guide is Choosing the Right Waterproof Sheet. The rest of this post is the engineering side.

What "waterproof" actually means for a bed sheet

Waterproof isn't a single specification. It's a range that runs from "resists a splash for a few seconds" through to "will hold standing water indefinitely without a drop passing through." Most home bedding products at the cheap end sit near the splash-resistant end. Ours are built to sit at the far end.

The relevant test for Nuru or oil massage is whether the sheet can hold half a litre of thin liquid pooled on the surface for the length of a session without any of it soaking through into the mattress. That's the practical bar, and it's harder to hit than it sounds. A lot of products sold as "water-resistant" are built for the odd spill, not a session's worth of gel.

TPU: what it is and why we use it

TPU stands for thermoplastic polyurethane. It's a plastic polymer that can be heat-formed into thin, flexible films. The characteristics that matter for bedding are that a TPU film is fully waterproof, breathable (unlike vinyl), soft to the touch, and can be laminated onto a fabric backing with heat instead of adhesive.

That last part is what makes TPU practical for a fitted sheet. A vinyl coating either has to be glued to fabric (which weakens over washing) or replaces the fabric entirely (which is what our V2 vinyl does). TPU can be heat-bonded directly to a fabric weave without adhesive, and the resulting laminate holds up well to regular washing.

The breathability point matters more than customers expect. A vinyl sheet doesn't let air through, so you sweat under it if you're lying still for a while. A TPU-laminated fabric lets water vapour through in one direction but blocks liquid water from the other. That gives you the waterproofing without the sauna effect.

The fabric side: Dacron and Spandex

The fabric layer under the TPU is a blend of 95% Dacron (branded polyester) and 5% Spandex (branded elastane).

Dacron is chosen for durability and colour retention. Cotton would feel softer at first but loses shape after ten or twenty washes. Dacron holds its shape and colour through several years of weekly use. Our sheets are rated at colour fastness 4.0 (on a 5-point scale), which is why we recommend washing them separately for the first cycle or two.

Spandex is added at 5% for stretch. Without it, the fitted skirt would either bunch on thinner mattresses or refuse to reach on thicker ones. The 5% ratio gives enough stretch to fit standard US and AU mattresses up to about 12 inches deep without sagging or over-tensioning.

The finish on the top surface is smooth and quiet. It doesn't rustle when you move on it, which is one of the reasons customers keep the sheet on the bed as a regular mattress protector rather than only pulling it out for massage.

TPU vs vinyl

Two materials cover most of the waterproof-bedding category, and we use both.

TPU-laminated fabric is what our Standard and Extreme sheets use. Soft feel, breathable, machine washable, tumble-dryer safe. Waterproof to the standard we described above. The trade-off is that TPU eventually fatigues under intense friction or oil exposure over years, so it's not the right choice for a dedicated Nuru surface used weekly.

Vinyl is what our V2 uses. Fully waterproof, slippery on the surface (which is what you want for Nuru gel), heavier and stiffer. Not machine washable, but wipe-clean in thirty seconds. Longer service life than TPU under intense oil and gel use. The trade-off is that it doesn't breathe and it's not something you'd want as your permanent bedsheet.

Care and longevity

Before washing, wipe away any excess gel or oil from the surface. Because the coating is non-absorbent, fluids can sit on the material and survive a wash if you skip this step. For best results, and to look after the waterproof coating, wash and dry at 60°C (140°F). Avoid bleach.

Wash the sheet on its own before first use. You may notice a slight smell from the coating out of the packet, and it fades after that first wash. Keep it away from light-coloured clothing in the wash to avoid colour transfer.

The Standard and Extreme sheets are engineered for the "one-sheet-does-everything" customer. The V2 vinyl is engineered for the customer who wants a dedicated Nuru surface with a different set of properties. Neither is better in absolute terms. They're built for different jobs.
V2 vinyl sheet comparison — different tool for a different job

For the full three-way comparison across Standard, Extreme, and V2 vinyl, see Choosing the Right Waterproof Sheet. For the broader Nuru context, see What Is Nuru Massage.

Eroticgel Nuru kit — waterproof sheet, powder, bowl, inflatable

Shop the waterproof range

Standard, Extreme, V2 Vinyl. Queen and King sizes. Free shipping over $59.99 in the US and Australia.

Shop waterproof sheets →